|
|
| (30 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| <div>
| | == General Information == |
|
| |
|
| == General Information ==
| | This page provides general information about the 3D Printers available at the makerspace, and directs makerspace members toward specific equipment pages for each printer. The 3D printers can be found inside the [[Clean Room]]. |
| </div>
| | |
| <div>The 3D printers can be found inside the [[Clean Room]].
| | If you have any issues with Clean Room equipment, the slack channels associated with this space include: #general, #shop-3d-printing, and #shop-laser. |
| | |
| | == ''Where do I find 3D models?'' == |
| | |
| | * [https://www.thingiverse.com/ Thingiverse] |
| | * [https://www.thangs.com/ Thangs] |
| | * [https://www.printables.com/ Printables] |
| | * [https://grabcad.com/ GrabCAD] |
| | * [https://www.myminifactory.com/ MyMiniFactory] |
| | * [https://www.tinkercad.com/things TinkerCAD Things] |
| | * [https://nasa3d.arc.nasa.gov/ NASA 3D Resources] |
|
| |
|
| If you have any issues with Clean Room equipment, the slack channels associated with this space include: #general, ##general, #shop-3d-printing, and #shop-laser.
| | == Recommended 3D Modeling Software == |
| | * [https://www.tinkercad.com/ TinkerCAD] - Browser based, cloud-based, approachable for makers of all ages |
| | * [https://www.autodesk.com/products/fusion-360/overview Fusion 360] - Cloud-based parametric 3D modeling software. Collaborative, powerful, free license available |
| | * [https://www.luban3d.com/ LuBan] - Has a number of fun features for scaling models to any size, lithographs, box making, extrusion, etc. We have a license for this software on-site, available on the PC located in the 3D Printing Area |
|
| |
|
| == Orientation == | | == FDM Printers == |
| | === Bambu Lab === |
|
| |
|
| The order of this document is to give some basic information of what will happen in the Clean Room during the training. This orientation assumes that they have gone through our general space orientation.<p>Do not operate any power equipment if you are under the influence of anything, in a hurry, are tired, or are not feeling well.</p>
| | '''Requires Basic FDM Orientation''' |
| <p>Inspect the equipment before using it.</p>
| |
|
| |
|
| == <span style="font-size: 24pt;">Equipment</span> ==
| | We have three Bambu Lab printers available: |
|
| |
|
| == Bamboo 3D Printer ==
| | * '''Bambu Lab X1 Carbon (2 units)''' |
| During the Orientation, you will be walked through the steps to set up and complete a print on the bamboo 3D Printer. [[File:BambuX1C.png|200px|right|middle]]
| | ** One unit is equipped with the AMS system for multicolor/multimaterial printing |
| | ** Build Volume: 256mm × 256mm × 256mm |
| | ** Nozzle Size: 0.4mm |
| | ** Materials Supported: PLA, PETG, ABS/ASA, Nylon, TPU, Soluble Support Materials |
| | ** Slicer Used: Bambu Studio |
|
| |
|
| '''Printing with one color:''' | | * '''Bambu Lab H2D (1 unit)''' |
| *Members will go through some various 3D print websites and pick/download a design that you want to 3D print.<br> | | ** Dual-nozzle system for multi-material printing |
| *Members will unload any previous filament in the machine, and add your preferred filament into the machine through the small white tube sticking out the back of the machine. | | ** Build Volume: 325mm × 320mm × 325mm (single nozzle), 300mm × 320mm × 325mm (shared space) |
| *Members will click load on the machine, and the machine should heat up, and purge the old filament. Make sure to check that the filament has been purged by looking at where it sticks out inside the machine. | | ** Nozzle Size: 0.4mm |
| *Open Bamboo studio and add your print. | | ** Materials Supported: PLA, PETG, ABS/ASA, Nylon, Carbon Fiber composites |
| *Look to make sure the plate in your machine, and the filament type matches what is put in Bamboo Studios. | | ** Slicer Used: Bambu Studio |
| *Make sure you have the infill you want selected. | |
| *Add any necessary supports to the piece. | |
| *Slice the Plate, you should get an estimated time that the print will take.
| |
| *Hit Print. | |
| *Stay with the print for the first few layers, to hopefully catch any early errors (You can click stop or pause when you notice these errors).<br> | |
| *Afterwards remove your print and get rid of the filament that has been purged onto the plate while the machine was preparing.
| |
| <div></div>
| |
|
| |
|
| == Bamboo 3D Printer with AMS ==
| | See Page: [[Bambu_3D_Printer|Bambu Lab 3D Printer]] |
| During the Orientation, you will be walked through the steps to set up and complete a print on the bamboo 3D Printer. [[File:BambuX1C.png|200px|right|middle]]
| |
|
| |
|
| '''Printing with multiple colors:'''
| | === Elegoo Orangestorm Giga === |
| *Members will go through various 3D print websites and pick/download a design that you want to 3D print.<br>
| |
| *Members will unload any previous filament in the machine, members will have to do this for each filament in the machine.
| |
| *Members will put their filament into the AMS system, we recommend only using three of the four possible colors, as that is when most issues start to occur. We also recommend not using the filaments that are on cardboard as it often gets stuck on the machine.
| |
| *Members will load the filament through a white tube on the inside of that machine. You will have to do this for every filament you use. Make sure to update the machine with what filament is in each slot.
| |
| *Members will click load on the machine, and the machine should heat up, and purge the old filament. Make sure to check that the filament has been purged by looking at where it sticks out inside the machine.
| |
| *Open Bamboo Studio and add your print.
| |
| *Look to make sure the plate in your machine, and the filament type match what is put in Bamboo Studios.
| |
| *Make sure you have the infill you want selected.
| |
| *You can now click on the paint bucket and add the different colors to your print, you can change the color by adding filament through bamboo studio. Remember that when using this machine it creates a lot of wasted filament because it has to purge filament every time there is a color change, so be smart about where color changes occur.
| |
| *Add any necessary supports to the piece.
| |
| *Slice the Plate, you should get an estimated time that the print will take.
| |
| *Hit Print.
| |
| *Stay with the print for the first few layers, to hopefully catch any early errors (You can click stop or pause when you notice these errors).<br>
| |
| *Afterwards remove your print and get rid of the filament that has been purged onto the plate while the machine was preparing.
| |
| <div></div>
| |
|
| |
|
| == Resin 3D Printer ==
| | '''Requires Large Format Printing Orientation / Permission from Jess to use''' |
| This will walk our potential members throught the resin printing orientation.[[File:3D Resin Printer.jpg|200px|right|middle]]
| | '''Currently still being integrated into the makerspace''' |
| *Members will find a model they would like to print and download it. We recommend picking one that is high definition, so people can see how accurate the printer is.
| |
| *After you download your file, go to Lychee (Resin 3D Printing Software)
| |
| *Go to the Lychee slicer and add your file/s to the program (Remember, the taller your design, the longer it takes)
| |
| *Click on model, and if to the right it says repair object, let it attempt to fix the print
| |
| *Scale your project to the size that you want. (You can do this by hitting scale on the left-hand side, clicking the miniature, and clicking/dragging any box. There is a yellow box in the center that you have to move over to see, but it scales the entire thing down uniformly<br>
| |
| *Lift each model off the ground.
| |
| *Rotate the model forward or backward (You want to make sure you're doing this in a way where the supports won't be extremely visible if they were to get stuck on your figure.
| |
| *Members will then add supports to their figure, making sure no stray supports get left in the body.
| |
| *Then you will hit prepare to prepare your model, which will give you some more options.<br>
| |
| *If needed, you can hollow your model (Typically you only do that with big resin prints, it's not worth doing on small ones.)
| |
| *Add drainage holes if necessary.
| |
| *Add a raft for your character (Should be automatically done with the supports if you did the automated ones)
| |
| *Make sure before you export that you have the correct resin type
| |
| *Export to files
| |
| *Clean the surface of the resin printer
| |
| *Put your file on a USB drive, turn on the resin printer, and select file. If you’ve cleaned the machine, click start
| |
| *Stay with it while it is printing the first couple of layers, so you can see and stop anything that goes wrong.
| |
| <div><span style="text-decoration: underline; font-size: 14pt;">'''Washing Station for Resin 3D Prints'''</span></div>
| |
| <div>Information Regarding Equipment, and picture of equipment to the left.</div>
| |
| [[File:3D Resin Washing.jpg|200px|right|middle]]
| |
|
| |
|
| <div><span style="text-decoration: underline; font-size: 14pt;">'''Curing Station for Resin 3D Prints'''</span></div>
| | * Build Volume: 800mm × 800mm × 1000mm |
| <div>Information Regarding Equipment, and picture of equipment to the left.</div>
| | * Nozzle Size: 0.6mm (will be changed to 1.0mm before orientation) |
| <div>[[File:3D Resin Curing.jpg|200px|right|middle]]</div>
| | * Materials Supported: PLA, PETG |
| | * Slicer Used: OrcaSlicer |
|
| |
|
| == Creality Ender Plus 5 3D Printer ==
| | See Page: [[Elegoo_Orangestorm_Giga_3d_Printer|Elegoo Orangestorm Giga 3D Printer]] |
| Information Regarding Equipment, and picture of equipment to the left.</div>
| |
| <div>
| |
| [[File:Ender5Plus.jpg|200px|right|middle]] | |
|
| |
|
| == Creality CR 10 3D Printer == | | == Printer Status == |
| Information Regarding Equipment, and picture of equipment to the left.</div>
| | See Page: [//printerstatus.bereamakerspace.org printerstatus.bereamakerspace.org] |
| [[File:CR10Max.jpg|200px|right|middle]]
| |
General Information
This page provides general information about the 3D Printers available at the makerspace, and directs makerspace members toward specific equipment pages for each printer. The 3D printers can be found inside the Clean Room.
If you have any issues with Clean Room equipment, the slack channels associated with this space include: #general, #shop-3d-printing, and #shop-laser.
Where do I find 3D models?
Recommended 3D Modeling Software
- TinkerCAD - Browser based, cloud-based, approachable for makers of all ages
- Fusion 360 - Cloud-based parametric 3D modeling software. Collaborative, powerful, free license available
- LuBan - Has a number of fun features for scaling models to any size, lithographs, box making, extrusion, etc. We have a license for this software on-site, available on the PC located in the 3D Printing Area
FDM Printers
Bambu Lab
Requires Basic FDM Orientation
We have three Bambu Lab printers available:
- Bambu Lab X1 Carbon (2 units)
- One unit is equipped with the AMS system for multicolor/multimaterial printing
- Build Volume: 256mm × 256mm × 256mm
- Nozzle Size: 0.4mm
- Materials Supported: PLA, PETG, ABS/ASA, Nylon, TPU, Soluble Support Materials
- Slicer Used: Bambu Studio
- Bambu Lab H2D (1 unit)
- Dual-nozzle system for multi-material printing
- Build Volume: 325mm × 320mm × 325mm (single nozzle), 300mm × 320mm × 325mm (shared space)
- Nozzle Size: 0.4mm
- Materials Supported: PLA, PETG, ABS/ASA, Nylon, Carbon Fiber composites
- Slicer Used: Bambu Studio
See Page: Bambu Lab 3D Printer
Elegoo Orangestorm Giga
Requires Large Format Printing Orientation / Permission from Jess to use
Currently still being integrated into the makerspace
- Build Volume: 800mm × 800mm × 1000mm
- Nozzle Size: 0.6mm (will be changed to 1.0mm before orientation)
- Materials Supported: PLA, PETG
- Slicer Used: OrcaSlicer
See Page: Elegoo Orangestorm Giga 3D Printer
Printer Status
See Page: printerstatus.bereamakerspace.org
